NEW PRODUCT RELEASE: Low Pressure Dual Nozzle CO2 Cryo Jet

Low Pressure Dual Nozzle CO2 Cryo Jet

February 26th 2013: Atlanta Georgia
Atlanta Special FX has invented another first in the industry. Over the past 5 years ATL FX has made improvements to existing CO2 cryo systems, as well as new products for the CO2 fog idustry that are now distributed in 33 countries and growing. This time the popular low pressure CO2 jet, used for smaller venue permanant installs, has been given a boost and converted into a double barrel. This new design utilizes cutting edge components and advance tube design to blast two dense streams of super cold CO2 cryo fog. The new LP Dual CO2 Jet is ideal for smaller venues that only have enough room for one CO2 Dewar tank but want two streams of cold fog. Available in 120v or 230v.

Distributor Opportunities Available

Contact Atlanta Special FX today for savings:
1-888-664-0097 or visit the web at http://www.atlspecialfx.com/collections/co2-cryo-fog-smoke

What Are The Differences Between All The CO2 and Cryo Labeled Products? FAQ

When talking about a CO2 Jet, you may have heard many names used before or you may have not. Whether you have or not, we will clarify some of the confusion here and get the nitty gritty on what each of the names means and how they relate to what you has become the focal point of todays special effects industry for both DJs and Nightclubs. When searching for a Cryo Cannon online you may have seen "CO2 Jet Blaster", "Handheld Cryo Gun", "Cryo Jet", or "C02 Jet" and have instantly become confused as to what the difference is between them.

First off, there is a difference between each one and therefore some things should be taken into account before following through with a click on that link titled "CO2 Jets For Sale". Essentially you have two categories, mounted and non-mounted jets, otherwise called handheld units. The handheld cryo gun falls into this category as by its name and of course its build since it is more like a fog sprayer than anything else. The mounted category contains the rest of the names mentioned above, Cryo Cannon, C02 Jet, CO2 Jet Blaster, Cryo Jet, and CO2 Jet. As a side note, all the units here fall under the special effects category and are used for special fx only.
So now onto the difference between the 5 names that sound so much alike. To start, a CO2 Jet, mistyped C02 Jet with a zero before the 2, is merely a piece of equipment that sprays Liquid Carbon Dioxide out of it to create white fog that is very cold. CO2 is the proper abbreviated name which has to do with the checmical makeup, therefore displaying the 2 in the name (ex. CO2 Cannon). A CO2 Jet Blaster is simply a CO2 Jet, but can be a higher output model, hence the "Blaster" at the end. For Cryo Cannon and Cryo Jet, these are names which have come to attention as the word "Cryo" means "Cold" or "Of Low Temperature". So when used in names such as Handheld Cryo Gun, Cryo Cannon, and Cryo Jet it is referring to low temperature output of what the unit will be spraying.

Having clarified the nomenclature of the names, we have a better understanding of what means what. With this said, and to get very technical with it, a CO2 Jet would be different from a Cryo Jet in the sense that the first deals with CO2 only and the second deals with anything cold. The same would go for Cryo Cannon and CO2 Cannon as well. We've already covered the mistype of C02 Jet so that's handled and out of the way. The CO2 Jet Blaster being a higher output model of a regular jet covers that name. The Handheld Cryo Gun name suggests it can sprray anything cold, but should only be used for spraying liquid carbon dioxide and not Liquid Nitrogen or anything else as it could ruin the machine. Another pointer to be made about this name is a Cryo Gun is also used in the medical field to freeze skin defects such as warts. You will want to make sure you are getting a special effects model such as the one pictured here at http://www.atlspecialfx.com/collections/co2-cryo-fog-smoke

How To Install A CO2 Cryo Fog Cooling System - Easy Install Techniques

If you have never installed a CO2 cryo jet system it may seem like a daunting task.  After you read through this short paragraph you will know all the ins and outs of installing your own CO2 cryo system with either high pressure tanks or low pressure Dewar tanks.  All the pros in the special effects world understand it doesn't take years of experience to install the CO2 cryo jets manufactured by Atlanta Special FX.  These cryo blasters are engineered to save you time and money.  They can be mounted in a variety of positions allowing for easy setup in all types of venues. 

If you notice on the photo to the left the lower, and back, mounting plates are designed to use screws for mounting to the floor, wall, and ceiling.  The multi mounting points allow the CO2 units to be installed right side up, lefts side, right side and upside down.  It also includes a pre drilled hole for easy mounting to a truss system using a J-clamp or C-clamp.  Once you have decided on your mounting the next thing to do is consider the location of your tanks in relation to your cryo nozzles.  Ideally you will want to keep your tanks as close to the CO2 jets as possible and always use tested and approved cryo hosing.  With that in mind, here are some general guidelines (NOT REQUIREMENTS) you will want to follow with your hose lengths:

1. Do your best to stay at 50-70 feet or less from your tanks when using low pressure Dewar tanks. (Closer is better)
2. Try to keep a direct line between your cryo jets and your tanks.  (The less 90 degree turns the better)
3. When using high pressure tanks you can use longer hoses (But if the CO2 sets in the hoses for extended periods of time between shots you will experience the noise before the white fog comes out)
4. It is optional to use T fittings and attach multiple jets to a single hose.

Now that you have decided the location of tanks and the location of cryo jets, you will need to distinguish between the cryo hose ends to determine which hooks to which.  The brass end is a standard CO2 fitting and attaches to the liquid CO2 bottle and the silver end attaches to the cryo jet.  Once you have attached your hoses you will now need to determine how you will power the jets on and off.  Most industry professionals use a 4 channel DMX dimmer / switch kit. (Sold Separately).  Others use items such as foot switches, push button firing systems, and even as manual as a surge protector.  The cryo jets only need a simple on off signal.  When the jet is on, CO2 plumes of fog will shoot from the nozzle and when they are off there will be no noise or fog.  The last things you will want to do are test fire the jets, without the gas on, listening for the clicking on/off sound.  Once you have tested the on/off it is time open your CO2 bottle.  Be sure the cryo unit is off, open the valve on top of the CO2 bottle all the way and the line will pressurize.  It is always good practice to leave the bottle closed until just before you need the effect.  This will ensure a nice, instant plume of fog when you power the CO2 fogger on.

CO2 fog is a great way to entertain your guests as well as provide stunning visual and audible effects while cooling the room down.  This is why CO2 foggers are a popular item for any nightclub venue.

We hope this article has shed a little light on your CO2 jet purchase.   If you have questions or comments, a professional technician is always standing by to assist you.

To order your own CO2 cryo cooling system contact:

Atlanta Special FX

404-644-2801

http://www.ATLspecialFX.com

or visit the CO2 cryo page direct at http://www.atlspecialfx.com/collections/co2-cryo-fog-smoke